Top 7 APM Power Module – Hobby Remote & App Controlled Vehicle Parts

As an Amazon Associate I earn from qualifying purchases.

1. Hobbypower

#ad

Hobbypower Power Module V1.0 with XT60 Plug for APM2.8 APM2.6 APM Pixhawk Flight Controller

#ad
Hobbypower #ad - The on-board switching regulator outputs 5. 3v and a maximum of 2. 25a from up to a 4S LiPo battery. Another signal cable connectors are used in Japan original fittings, you can output 5.

3 dc, non-domestic joint, so APM flight control board and reliable connection between the power supply module. The power module comes completely assembled with Deans connectors, and wrapped in shrink tubing for protection. The apm power module is a simple way of providing your apm fc with clean power from a lipo battery as well as current consumption and battery voltage measurements, all through a 6-pos cable.

Used to detect the battery voltage and the battery current, flight control board receives two signals, calculate the remaining battery power, estimate the remaining flight time. In addition the module also comes with bec function, 3a maximum continuous current for the flight control board to provide a stable power supply.
BrandHobbypower #ad
ManufacturerHobbypower #ad
Part NumberPower Module

2. HobbySoar

#ad

HobbySoar Power Module Output BEC 3A with XT60 Plug for APM2.5 APM2.6 APM2.8 APM Pixhawk Flight Controller

#ad
HobbySoar #ad - It is not designed to power servos. Pls do not use this to power the servo. Otherwise, due to the large current of servo system, please use the BEC to power the servo system.

The apm power module is a simple way of providing your APM FC with clean power from a LiPo battery as well as current consumption and battery voltage measurements, all through a 6-pin cable. The power module comes completely assembled with XT60 connectors, and wrapped in shrink tubing for protection. For sale is power module which is suitable for APM2. 5/2. 6, pixhawk flight controller, have soldered already, ready to work!. Input voltage: 6~28v, max current sensing: 90A. Note: the power module is only designed to flight controller, rc receiver and apm accessories gps, it will seriously affect the reliability of the flight control equipment. If the kit is equipped with a servo, 3DR radio.
BrandHobbySoar #ad
ManufacturerShareGoo #ad
Weight0.04 Pounds
Part Number43234-2762

3. elechawk

#ad

Pixhawk Power Module 5.3V BEC XT60 Connectors for APM2.8 2.6 Quadcopter

#ad
elechawk #ad - 6-pin 1. 25 connector suitable for Pixhawk/APM. There is a 220uf electrolytic capacitor in the Power Module can effectively prevent destroyed by a high voltage pulse. Used up to 28v 6s lipo and at a maximum of 90A. The outputs voltage of bec is about 5. 3v. The power module is ready to use with XT60 connectors pre-fitted, and shrink wrapped for protection. Maximum bec output continuous current: 2. 25a.
Brandelechawk #ad
Manufacturerelechawk #ad
Part Number3867

4. QWinOut

#ad

QWinOut Power Module Current Module Female Male Plug with 5.3V DC BEC for APM 2.8 PIXHAWK Flight Controller APM2.6 2.5 2.52 RC DIY Drone Accessories

#ad
QWinOut #ad - For apm 2. 5 2. 6 2. 8 pix pixhawK. The on-board switching regulator outputs 5. 3v and a maximum of 2. 25a from up to a 4S LiPo battery. Use your aircraft's own ESC/BEC for that. Max input voltage: 25V. It is notdesigned to power servos. Note: the power module is only designed to power apm, a rc receiver and APM accessories GPS, 3DR radio. The power module comes completely assembled with Deans connectors, and wrapped in shrink tubing for protection.
BrandQWinOut #ad
ManufacturerQWinOut #ad
Part NumberM07638

5. Hobbypower

#ad

Hobbypower Power Module V1.0 for Pixhawk Apm2.5 Apm2.6 Ardupilot Mega Flight Controller

#ad
Hobbypower #ad - Voltage and current measurement configured for 5V ADC. Newest version, have soldered already, ready to work! Top quality and 100% brand new. Max current sensing: 90A. Input voltage: 6~28V support 30V.
BrandHobbypower #ad
ManufacturerHobbypower #ad
Weight0.02 Pounds
Part Number4977
Model4977

6. HolyBro

#ad

HolyBro APM Power Module 12S, PM02 V3

#ad
HolyBro #ad - 6-pos molex cable plugs directly to APM/Pix32's 'PM' connector. Voltage and current measurement configured for 5V ADC. Max input voltage: 60V. Switching regulator outputs 5. 2v and 3A max. Max current sensing: 120A.
BrandHolyBro #ad
ManufacturerHolybro #ad
Weight0.07 Pounds

7. Xiangtat

#ad

Xiangtat APM Power Module V1.0 XT60 Plug Current Sensor for APM2.8 APM2.6 APM Pixhawk Flight Controller

#ad
Xiangtat #ad - It is not designed to power servos. 6-pos df13 cable plugs directly to APM 2. 5's 'pm' connector. Note: the power module is only designed to power apm, a rc receiver and APM accessories GPS, 3DR radio. Switching regulator outputs 5. 3v and 3A max. Max input voltage: 30V, Max current sensing: 90A. Voltage and current measurement configured for 5V ADC. Use your aircraft's own ESC/BEC for that.
BrandXiangtat #ad
ManufacturerLotus Mall #ad
Part NumberPower Module